Home/DIAGNOSTIC TROUBLE CODE INDEX: ANTI-LOCK BRAKE SYSTEM (ABS) - DTC: ANTI-LOCK BRAKE SYSTEM CONTROL MODULE (ABS)

DIAGNOSTIC TROUBLE CODE INDEX: ANTI-LOCK BRAKE SYSTEM (ABS) - DTC: ANTI-LOCK BRAKE SYSTEM CONTROL MODULE (ABS)

Thursday, August 12, 2021

by JLR Dealer Tool Kits Worldwide shipping

DIAGNOSTIC TROUBLE CODE INDEX: ANTI-LOCK BRAKE SYSTEM (ABS) - DTC: ANTI-LOCK BRAKE SYSTEM CONTROL MODULE (ABS) (G1566096)

DESCRIPTION AND OPERATION

ANTI-LOCK BRAKE SYSTEM CONTROL MODULE (ABS)

CAUTION:

Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.

NOTES:

If a control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component.
Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the manufacturer-approved diagnostic system).
When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places, and with an up-to-date calibration certificate. When testing resistance always take the resistance of the digital multimeter leads into account.
Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.
Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific customer complaint and carry out the recommendations as required.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Anti-lock Brake System Control Module (ABS). For additional diagnosis and testing information, refer to the relevant Diagnosis and Testing section in the workshop manual.

DTC	DESCRIPTION	POSSIBLE CAUSES	ACTION
C0030-38	Left Front Tone Wheel - Signal frequency incorrect	Front left wheel speed sensor reluctor ring damaged Front left wheel bearing failure Front left wheel/tire size incorrect	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Check the integrity of the front left wheel speed sensor reluctor ring Check the front left wheel bearing Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the front left wheel and tire for condition and balance. Check and tighten the wheel nuts
C0031-11	Left Front Wheel Speed Sensor - Circuit short to ground	NOTE: Circuit reference FL_PWR Front left wheel speed sensor power circuit short circuit to ground	Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to ground
C0031-12	Left Front Wheel Speed Sensor - Circuit short to battery	NOTE: Circuit reference FL_PWR Front left wheel speed sensor power circuit short circuit to power	Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to power
C0031-14	Left Front Wheel Speed Sensor - Circuit short to ground or open	NOTE: Circuit reference FL_RTN Front left wheel speed sensor signal circuit short circuit to ground, open circuit, high resistance	Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground, open circuit, high resistance. Using the manufacturer approved diagnostic system, check datalogger signal - Left Front Wheel Speed Sensor Input (0x2B06)
C0031-1C	Left Front Wheel Speed Sensor - Circuit voltage out of range	NOTE: Circuit reference FL_PWR Front left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance	Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0031-25	Left Front Wheel Speed Sensor - Signal shape/waveform failure	NOTE: Circuit reference FL_RTN Front left wheel speed sensor signal circuit short circuit to ground Front left wheel speed sensor internal failure	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground Using the manufacturer approved diagnostic system, clear the DTCs and retest. If the fault persists, install a new front left wheel speed sensor
C0031-29	Left Front Wheel Speed Sensor - Signal invalid	NOTE: Circuit reference FL_PWR / FL_RTN Front left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance Front left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0031-2F	Left Front Wheel Speed Sensor - Signal erratic	NOTE: Circuit reference FL_RTN Front left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0031-31	Left Front Wheel Speed Sensor - No signal	NOTE: Circuit reference FL_RTN Front left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0031-4A	Left Front Wheel Speed Sensor - Incorrect component installed	Incorrect front left wheel speed sensor installed	Install the correct front left wheel speed sensor
C0031-62	Left Front Wheel Speed Sensor - Signal compare failure	NOTE: Circuit reference FL_PWR / FL_RTN Front left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance Front left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0031-66	Left Front Wheel Speed Sensor - Signal has too many transitions/events	NOTE: Circuit reference FL_PWR / FL_RTN Front left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance Front left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance Front left wheel/tire size incorrect	Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the front left wheel and tire for condition and balance. Check and tighten the wheel nuts
C0031-76	Left Front Wheel Speed Sensor - Wrong mounting position	Front left wheel speed sensor incorrectly installed Incorrect front left wheel speed sensor installed	Install the front left wheel speed sensor correctly Install the correct front left wheel speed sensor
C0033-38	Right Front Tone Wheel - Signal frequency incorrect	Front right wheel speed sensor reluctor ring damaged Front right wheel bearing failure Front right wheel/tire size incorrect	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Check the integrity of the front right wheel speed sensor reluctor ring Check the front right wheel bearing Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the front right wheel and tire for condition and balance. Check and tighten the wheel nuts
C0034-11	Right Front Wheel Speed Sensor - Circuit short to ground	NOTE: Circuit reference FR_PWR Front right wheel speed sensor power circuit short circuit to ground	Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to ground
C0034-12	Right Front Wheel Speed Sensor - Circuit short to battery	NOTE: Circuit reference FR_PWR Front right wheel speed sensor power circuit short circuit to power	Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to power
C0034-14	Right Front Wheel Speed Sensor - Circuit short to ground or open	NOTE: Circuit reference FR_RTN Front right wheel speed sensor signal circuit short circuit to ground, open circuit, high resistance	Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground, open circuit, high resistance. Using the manufacturer approved diagnostic system, check datalogger signal - Right Front Wheel Speed Sensor Input (0x2B07)
C0034-1C	Right Front Wheel Speed Sensor - Circuit voltage out of range	NOTE: Circuit reference FR_PWR Front right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance	Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0034-25	Right Front Wheel Speed Sensor - Signal shape/waveform failure	NOTE: Circuit reference FR_PWR Front right wheel speed sensor signal circuit short circuit to ground Front right wheel speed sensor internal failure	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground Using the manufacturer approved diagnostic system, clear the DTCs and retest. If the fault persists, install a new front right wheel speed sensor
C0034-29	Right Front Wheel Speed Sensor - Signal invalid	NOTE: Circuit reference FR_PWR / FR_RTN Front right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance Front right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0034-2F	Right Front Wheel Speed Sensor - Signal erratic	NOTE: Circuit reference FR_RTN Front right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0034-31	Right Front Wheel Speed Sensor - No signal	NOTE: Circuit reference FR_RTN Front right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0034-4A	Right Front Wheel Speed Sensor - Incorrect component installed	Incorrect front right wheel speed sensor installed	Install the correct front right wheel speed sensor
C0034-62	Right Front Wheel Speed Sensor - Signal compare failure	NOTE: Circuit reference FR_PWR / FR_RTN Front right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance Front right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0034-66	Right Front Wheel Speed Sensor - Signal has too many transitions/events	NOTE: Circuit reference FR_PWR / FR_RTN Front right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance Front right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance Front right wheel/tire size incorrect	Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the front right wheel and tire for condition and balance. Check and tighten the wheel nuts
C0034-76	Right Front Wheel Speed Sensor - Wrong mounting position	Front right wheel speed sensor incorrectly installed Incorrect front right wheel speed sensor installed	Install the front right wheel speed sensor correctly Install the correct front right wheel speed sensor
C0036-38	Left Rear Tone Wheel - Signal frequency incorrect	Rear left wheel speed sensor reluctor ring damaged Rear left wheel bearing failure Rear left wheel/tire size incorrect	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Check the integrity of the rear left wheel speed sensor reluctor ring Check the rear left wheel bearing Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the rear left wheel and tire for condition and balance. Check and tighten the wheel nuts
C0037-11	Left Rear Wheel Speed Sensor - Circuit short to ground	NOTE: Circuit reference RL_PWR Rear left wheel speed sensor power circuit short circuit to ground	Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to ground
C0037-12	Left Rear Wheel Speed Sensor - Circuit short to battery	NOTE: Circuit reference RL_PWR Rear left wheel speed sensor power circuit short circuit to power	Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to power
C0037-14	Left Rear Wheel Speed Sensor - Circuit short to ground or open	NOTE: Circuit reference RL_RTN Rear left wheel speed sensor signal circuit short circuit to ground, open circuit, high resistance	Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground, open circuit, high resistance. Using the manufacturer approved diagnostic system, check datalogger signal - Left Rear Wheel Speed Sensor Input (0x2B08)
C0037-1C	Left Rear Wheel Speed Sensor - Circuit voltage out of range	NOTE: Circuit reference RL_PWR Rear left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance	Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0037-25	Left Rear Wheel Speed Sensor - Signal shape/waveform failure	NOTE: Circuit reference RL_PWR Rear left wheel speed sensor signal circuit short circuit to ground Rear left wheel speed sensor internal failure	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground Using the manufacturer approved diagnostic system, clear the DTCs and retest. If the fault persists, install a new rear left wheel speed sensor
C0037-29	Left Rear Wheel Speed Sensor - Signal invalid	NOTE: Circuit reference RL_PWR / RL_RTN Rear left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance Rear left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0037-2F	Left Rear Wheel Speed Sensor - Signal erratic	NOTE: Circuit reference RL_RTN Rear left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0037-31	Left Rear Wheel Speed Sensor - No signal	NOTE: Circuit reference RL_RTN Rear left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0037-4A	Left Rear Wheel Speed Sensor - Incorrect component installed	Incorrect rear left wheel speed sensor installed	Install the correct rear left wheel speed sensor
C0037-62	Left Rear Wheel Speed Sensor - Signal compare failure	NOTE: Circuit reference RL_PWR / RL_RTN Rear left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance Rear left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C0037-66	Left Rear Wheel Speed Sensor - Signal has too many transitions/events	NOTE: Circuit reference RL_PWR / RL_RTN Rear left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance Rear left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance Rear left wheel/tire size incorrect	Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the rear left wheel and tire for condition and balance. Check and tighten the wheel nuts
C0037-76	Left Rear Wheel Speed Sensor - Wrong mounting position	Rear left wheel speed sensor incorrectly installed Incorrect rear left wheel speed sensor installed	Install the rear left wheel speed sensor correctly Install the correct rear left wheel speed sensor
C0039-38	Right Rear Tone Wheel - Signal frequency incorrect	Rear right wheel speed sensor reluctor ring damaged Rear right wheel bearing failure Rear right wheel/tire size incorrect	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Check the integrity of the rear right wheel speed sensor reluctor ring Check the rear right wheel bearing Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the rear right wheel and tire for condition and balance. Check and tighten the wheel nuts
C003A-11	Right Rear Wheel Speed Sensor - Circuit short to ground	NOTE: Circuit reference RR_PWR Rear right wheel speed sensor power circuit short circuit to ground	Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to ground
C003A-12	Right Rear Wheel Speed Sensor - Circuit short to battery	NOTE: Circuit reference RR_PWR Rear right wheel speed sensor power circuit short circuit to power	Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to power
C003A-14	Right Rear Wheel Speed Sensor - Circuit short to ground or open	NOTE: Circuit reference RR_RTN Rear right wheel speed sensor signal circuit short circuit to ground, open circuit, high resistance	Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground, open circuit, high resistance. Using the manufacturer approved diagnostic system, check datalogger signal - Right Rear Wheel Speed Sensor Input (0x2B09)
C003A-1C	Right Rear Wheel Speed Sensor - Circuit voltage out of range	NOTE: Circuit reference RR_PWR Rear right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance	Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C003A-25	Right Rear Wheel Speed Sensor - Signal shape/waveform failure	NOTE: Circuit reference RR_PWR Rear right wheel speed sensor signal circuit short circuit to ground Rear right wheel speed sensor internal failure	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground Using the manufacturer approved diagnostic system, clear the DTCs and retest. If the fault persists, install a new rear right wheel speed sensor
C003A-29	Right Rear Wheel Speed Sensor - Signal invalid	NOTE: Circuit reference RR_PWR / RR_RTN Rear right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance Rear right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C003A-2F	Right Rear Wheel Speed Sensor - Signal erratic	NOTE: Circuit reference RR_RTN Rear right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C003A-31	Right Rear Wheel Speed Sensor - No signal	NOTE: Circuit reference RR_RTN Rear right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C003A-4A	Right Rear Wheel Speed Sensor - Incorrect component installed	Incorrect rear right wheel speed sensor installed	Install the correct rear right wheel speed sensor
C003A-62	Right Rear Wheel Speed Sensor - Signal compare failure	NOTE: Circuit reference RR_PWR / RR_RTN Rear right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance Rear right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C003A-66	Right Rear Wheel Speed Sensor - Signal has too many transitions/events	NOTE: Circuit reference RR_PWR / RR_RTN Rear right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance Rear right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance Rear right wheel/tire size incorrect	Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the rear right wheel and tire for condition and balance. Check and tighten the wheel nuts
C003A-76	Right Rear Wheel Speed Sensor - Wrong mounting position	Rear right wheel speed sensor incorrectly installed Incorrect rear right wheel speed sensor installed	Install the rear right wheel speed sensor correctly Install the correct rear right wheel speed sensor
C0061-24	Lateral Acceleration Sensor - Signal stuck high	Lateral acceleration sensor internal failure	NOTE: The sensor is located within/integral to the restraints control module Using the manufacturer approved diagnostic system, check the restraints control module for related DTCs and refer to the relevant DTC index
C0061-64	Lateral Acceleration Sensor - Signal plausibility failure	Lateral acceleration sensor internal failure	NOTE: The sensor is located within/integral to the restraints control module Using the manufacturer approved diagnostic system, check the restraints control module for related DTCs and refer to the relevant DTC index
C0062-64	Longitudinal Acceleration Sensor - Signal plausibility failure	Longitudinal acceleration sensor internal failure	NOTES: The sensor is located within/integral to the restraints control module This DTC can be set if the vehicle is being tested on chassis dyno rollers Using the manufacturer approved diagnostic system, check the restraints control module for related DTCs and refer to the relevant DTC index
C0063-64	Yaw Rate Sensor - Signal plausibility failure	Yaw rate sensor internal failure	NOTES: The sensor is located within/integral to the restraints control module This DTC can be set if the vehicle is being tested on chassis dyno rollers Using the manufacturer approved diagnostic system, check the restraints control module for related DTCs and refer to the relevant DTC index
C0064-64	Roll Rate Sensor - Signal plausibility failure	Roll rate sensor internal failure	NOTES: The sensor is located within/integral to the restraints control module This DTC can be set if the vehicle is being tested on chassis dyno rollers Using the manufacturer approved diagnostic system, check the restraints control module for related DTCs and refer to the relevant DTC index
C006B-00	Stability System Active Too Long - No sub type information	Wheel bearing failure Wheel speed sensor reluctor ring fault High speed CAN bus (chassis or powertrain) circuits short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: If this DTC is logged for the first time, the only action is to clear the DTC. Should the DTC reoccur, follow the actions as described below Check the integrity of the wheel bearings Using the manufacturer approved diagnostic system, check datalogger signals - Left Front Wheel Speed Sensor Input (0x2B06) - Right Front Wheel Speed Sensor Input (0x2B07) - Left Rear Wheel Speed Sensor Input (0x2B08) - Right Rear Wheel Speed Sensor Input (0x2B09) Using the manufacturer approved diagnostic system, perform a CAN network integrity test. Refer to the electrical circuit diagrams and check the high speed CAN bus (chassis and powertrain) circuits for short circuit to ground, short circuit to power, open circuit, high resistance
C101F-49	Generic Valve Failure - Internal electronic failure	Anti-lock brake system hydraulic control unit internal failure	Using the manufacturer approved diagnostic system, clear the DTCs and retest. If the fault persists, install a new anti-lock brake system hydraulic control unit
C1054-68	System Functionality Reduced By Diagnostic Request - Event information	Diagnostic routine DC00 in progress	NOTE: This DTC is set when routine DC00 is performed (Engineering only) Exit the diagnostic routine
C1109-24	Vehicle Dynamics Control Switch - Signal stuck high	Dynamic stability control switch stuck active	Test the operation of the dynamic stability control switch. If fault persists, install a new terrain response switchpack
C1A90-12	Wheel Speed Sensor Supply - Circuit short to battery	Wheel speed sensor supply circuit(s) short circuit to power	Refer to the electrical circuit diagrams and check the wheel speed sensor supply circuits for short circuit to power
C1A95-01	Wheel Speed Sensor Supply - General electrical failure	Wheel speed sensor circuit(s) short circuit to ground, short circuit to power, open circuit, high resistance Battery/charging system fault	Refer to the electrical circuit diagrams and check the wheel speed sensor circuits for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the relevant section of the workshop manual and test the battery and charging system
C1A95-62	Wheel Speed Sensor - Signal compare failure	Wheel speed sensor circuit(s) short circuit to ground, short circuit to power, open circuit, high resistance Wheel speed sensor reluctor ring fault Wheel bearing failure Wheel and/or tire size incorrect	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the wheel speed sensor circuits for short circuit to ground, short circuit to power, open circuit, high resistance Using the manufacturer approved diagnostic system, check datalogger signals - Left Front Wheel Speed Sensor Input (0x2B06) - Right Front Wheel Speed Sensor Input (0x2B07) - Left Rear Wheel Speed Sensor Input (0x2B08) - Right Rear Wheel Speed Sensor Input (0x2B09) Check the integrity of the wheel bearings Check that the wheel and tire sizes are correct to the vehicle specification
C1A95-64	Wheel Speed Sensor - Signal plausibility failure	Wheel speed sensor circuit(s) short circuit to ground, short circuit to power, open circuit, high resistance Wheel speed sensor reluctor ring fault Wheel bearing failure Wheel and/or tire size incorrect	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check the wheel speed sensor circuits for short circuit to ground, short circuit to power, open circuit, high resistance Using the manufacturer approved diagnostic system, check datalogger signals - Left Front Wheel Speed Sensor Input (0x2B06) - Right Front Wheel Speed Sensor Input (0x2B07) - Left Rear Wheel Speed Sensor Input (0x2B08) - Right Rear Wheel Speed Sensor Input (0x2B09) Check the integrity of the wheel bearings Check that the wheel and tire sizes are correct to the vehicle specification
C1A95-76	Wheel Speed Sensor - Wrong mounting position	Wheel speed sensor(s) incorrectly installed Incorrect wheel speed sensor(s) installed	Check the wheel speed sensors installation Install a new wheel speed sensor as necessary
C1A96-64	Brake Light Switch - Signal plausibility failure	Brake pedal switch incorrectly installed Brake pedal switch circuit short circuit to ground, short circuit to power, open circuit, high resistance	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Check the brake pedal switch installation Refer to the electrical circuit diagrams and check the brake pedal switch circuit for short circuit to ground, short circuit to power, open circuit, high resistance
C1A99-14	Pressure Sensor - Circuit short to ground or open	Anti-lock brake system hydraulic control unit internal failure	Using the manufacturer approved diagnostic system, clear the DTCs and retest. If the fault persists, install a new anti-lock brake system hydraulic control unit
C1A99-28	Pressure Sensor - Signal bias level out of range / zero adjustment failure	Anti-lock brake system hydraulic control unit internal failure	Using the manufacturer approved diagnostic system, clear the DTCs and retest. If the fault persists, install a new anti-lock brake system hydraulic control unit
C1B00-29	Steering Angle Sensor - Signal invalid	Steering angle sensor module incorrectly installed Steering angle sensor module fault	Check the steering angle sensor module installation Using the manufacturer approved diagnostic system, check the steering angle sensor module for related DTCs and refer to the relevant DTC index
C1B00-54	Steering Angle Sensor - Missing calibration	Steering angle sensor module fault	Using the manufacturer approved diagnostic system, check the steering angle sensor module for related DTCs and refer to the relevant DTC index
C1B00-64	Steering Angle Sensor - Signal plausibility failure	Steering angle sensor module incorrectly installed Steering angle sensor module internal failure Yaw rate sensor incorrect installation	NOTE: This DTC is set when there is conflicting information coming from the steering angle sensor and the yaw rate sensor Check the steering angle sensor module installation Using the manufacturer approved diagnostic system, check the steering angle sensor module for related DTCs and refer to the relevant DTC index Check the yaw rate sensor installation
C1B00-76	Steering Angle Sensor - Wrong mounting position	Steering angle sensor module incorrectly installed Steering angle sensor module internal failure	Check the steering angle sensor module installation Using the manufacturer approved diagnostic system, check the steering angle sensor module for related DTCs and refer to the relevant DTC index
C1B00-92	Steering Angle Sensor - Performance or incorrect operation	Steering angle sensor module incorrectly installed Steering angle sensor module internal failure	Check the steering angle sensor module installation Using the manufacturer approved diagnostic system, check the steering angle sensor module for related DTCs and refer to the relevant DTC index
C1B02-16	Return Pump - Circuit voltage below threshold	NOTE: Circuit reference PUMP SUPPLY / PUMP GND Anti-lock brake system hydraulic control unit pump circuit short circuit to ground, open circuit, high resistance	Refer to the electrical circuit diagrams and check the anti-lock brake system hydraulic control unit pump circuit for short circuit to ground, open circuit, high resistance
C1B02-49	Return Pump - Internal electronic failure	Anti-lock brake system control module internal failure	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Using the manufacturer approved diagnostic system, clear the DTCs and retest. If the fault persists, install a new anti-lock brake system control module
C1B22-24	Hill Descent Switch - Signal stuck high	Hill descent control switch stuck active	Test the operation of the hill descent control switch. If fault persists, install a new terrain response switchpack
C2009-95	Front Axle Wheel Speed Sensors Swapped - Incorrect assembly	Front wheel speed sensor connectors transposed	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check that the front wheel speed sensors are connected correctly
C200A-95	Rear Axle Wheel Speed Sensors Swapped - Incorrect assembly	Rear wheel speed sensor connectors transposed	NOTE: After clearing the DTCs, the warning indicator(s) may not extinguish until the vehicle speed has exceeded 10mph (15kph) Refer to the electrical circuit diagrams and check that the rear wheel speed sensors are connected correctly
U0001-81	High Speed CAN Communication Bus - Invalid serial data received	Invalid data received from another control module via the high speed CAN bus (chassis and powertrain)	NOTE: Do NOT install a new ABS module as this will NOT rectify the fault Using the manufacturer approved diagnostic system, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0001-82	High Speed CAN Communication Bus - Alive/sequence counter incorrect / not updated	Invalid data received from another control module via the high speed CAN bus (chassis and powertrain)	NOTE: Do NOT install a new ABS module as this will NOT rectify the fault Using the manufacturer approved diagnostic system, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0001-83	High Speed CAN Communication Bus - Value of signal protection calculation incorrect	Invalid data received from another control module via the high speed CAN bus (chassis and powertrain)	NOTE: Do NOT install a new ABS module as this will NOT rectify the fault Using the manufacturer approved diagnostic system, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0001-87	High Speed CAN Communication Bus - Missing message	Missing message from another control module via the high speed CAN bus (chassis and powertrain)	NOTE: Do NOT install a new ABS module as this will NOT rectify the fault Using the manufacturer approved diagnostic system, check the snapshot data to determine the missing message source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0001-88	High Speed CAN Communication Bus - Bus off	High speed CAN bus (chassis or powertrain) circuits short circuit to ground, short circuit to power, open circuit, high resistance	Using the manufacturer approved diagnostic system, perform a CAN network integrity test. Refer to the electrical circuit diagrams and check the high speed CAN bus (chassis and powertrain) circuits for short circuit to ground, short circuit to power, open circuit, high resistance
U0074-88	Control Module Communication Bus "B" Off - Bus off	High speed CAN bus (chassis or powertrain) circuits short circuit to ground, short circuit to power, open circuit, high resistance	Using the manufacturer approved diagnostic system, perform a CAN network integrity test. Refer to the electrical circuit diagrams and check the high speed CAN bus (chassis and powertrain) circuits for short circuit to ground, short circuit to power, open circuit, high resistance
U0300-00	Internal Control Module Software Incompatibility - No sub type information	The anti-lock brake system control module is not compatible with the vehicle	Check the anti-lock brake system control module part number, install the correct part as required. Clear DTC and retest. To confirm the repair and extinguish the warning lamps, clear the DTC, cycle the ignition state to off, then return the ignition state to on and wait up to 10 seconds
U0405-68	Invalid Data Received From Cruise Control Module - Event information	Missing/invalid data from the adaptive speed control module	Using the manufacturer approved diagnostic system, check the adaptive speed control module for related DTCs and refer to the relevant DTC index
U201A-55	Control Module Main Calibration Data - Not configured	Anti-lock brake system control module is not correctly configured	Using the manufacturer approved diagnostic system, re-configure the anti-lock brake system control module with the latest level software
U2300-54	Central Configuration - Missing calibration	Car configuration file mismatch with vehicle specification	Using the manufacturer approved diagnostic system, re-configure the anti-lock brake system control module with the latest level software. If the fault persists, check and up-date the car configuration file as necessary
U3000-44	Control Module - Data memory failure	Anti-lock brake system control module internal failure	Using the manufacturer approved diagnostic system, re-configure the anti-lock brake system control module with the latest level software. If the fault persists, install a new anti-lock brake system control module
U3000-46	Control Module - Calibration/parameter memory failure	Anti-lock brake system control module is not correctly configured	Using the manufacturer approved diagnostic system, re-configure the anti-lock brake system control module with the latest level software. Clear the DTCs and retest. If the fault persists, install a new anti-lock brake system control module
U3000-48	Control Module - Supervision software failure	Anti-lock brake system control module is not correctly configured	Using the manufacturer approved diagnostic system, re-configure the anti-lock brake system control module with the latest level software. Clear the DTCs and retest. If the fault persists, install a new anti-lock brake system control module
U3000-49	Control Module - Internal electronic failure	Anti-lock brake system control module internal failure	Using the manufacturer approved diagnostic system, clear the DTCs and retest. If the fault persists, install a new anti-lock brake system control module
U3000-4B	Control Module - Over temperature	Anti-lock brake system hydraulic control unit valve overheat protection has been activated	NOTE: This DTC may be set if the manufacturer approved diagnostic system has been operating the valves for a prolonged period Allow sufficient time for the unit to cool. Using the manufacturer approved diagnostic system, clear the DTCs and retest
U3000-51	Control module - Not programmed	Anti-lock brake system control module is not correctly configured	Using the manufacturer approved diagnostic system, re-configure the anti-lock brake system control module with the latest level software. Clear the DTCs and retest. If the fault persists, install a new anti-lock brake system control module
U3000-55	Control module - Not configured	Car configuration file mismatch with vehicle specification	Using the manufacturer approved diagnostic system, check and up-date the car configuration file as necessary
U3003-17	Battery voltage - Circuit voltage above threshold	Battery/charging system fault	Using the manufacturer approved diagnostic system, check datalogger signal - ECU Power Supply Voltage (0xD111). Refer to the relevant section of the workshop manual and test the battery and charging system
U3006-16	Control Module Input Power "A" - Circuit voltage below threshold	Battery/charging system fault Anti-lock brake system control module power or ground circuit high resistance	Using the manufacturer approved diagnostic system, check datalogger signal - ECU Power Supply Voltage (0xD111). Refer to the relevant section of the workshop manual and test the battery and charging system Refer to the electrical circuit diagrams and check the anti-lock brake system control module power and ground circuits for high resistance

What is the difference between IDS and SDD Pathfinder & Cloud?

Is IDS Integrated Diagnostic Software used on Jaguars 1995 to 2010

Yes the old program to work on the jags before 2005 is called IDS. We have v128 and V131 that have this software included and only runs on win XP sp3

V131 in Xp only ok for

Jags 1995 to 2010

Land rovers 2006 to 2010

Better one to use is the V163 or Higher that comes with order the latest SDD and can use jags and land rover 2006 to 2015

SDD Software used on Jaguars and Land rovers after 2005 to 2015

Yes after 2006 IDS went out and in came SDD with better interface and functions .starts from 2006 to 2015

Can use Pass thru cables from many diffrent suppliers

Activation for JLR SDD of latest version

Pathfinder Software used with DOIP VCI 2015 to 2022 Models

https://www.jlridssddmongoose.com/home/activation-for-jlr-pathfinder-of-latest-version/

2015 to 2022 Cars can use Pathfinder

Cloud Cars 2022 to 2023 and future

Some 2022 and 23 Models needs to use the Cloud Software in Topix

Will my Land Rover work with the JLR SDD Software?

Will my Land Rover / Jaguar work with the JLR SDD Software?

As long as your Jaguar is between 1995 and 2021+ and your Land Rover is between 2005-2021+, our kits will work. (OBD2 port must be present.) Note for newer models its required to have the higher version for the software to work best. check features page for years and models supported for each kit.

i Have an old Model Jaguar From 1995 to 2006. Can these kits work for me ?

Older models of Jaguar are Supported in V131 or Lower Versions. IDS is the software used for these models.

The V131 Software has both the SDD & IDS.

To use IDS for the older models its required to type in the VIN number and then Identify to bring up the pop up window that loads IDS.

For models after 2006 can simply Read the Vin without entering manually to use the SDD Software as support of IDS ends in 2005 and they switched over the the SDD.

Does the Kit support Flashing / Programming Modules ?

Yes Programming Functions are supported in our Kits.

You can Flash update Modules with newer firmwares or Program Virgin Parts to match the Car Vin

Is Key and KVM Programming Supported

Yes is Supported in Some Packages we offer

Can i Do Programming with this diagnostics Kit

Can update the Software in the modules like at the Dealers ?

Yes sure

These are Pro level kits and support software updating the ECU Softwares to newer ones.

Each Module has a Flash memory that controls how it works. Over time these get updated to enhance car functions

Normally need to visit the Dealer to do this . But now with our kits you can do from your home workshop or garage.

Can i program new Virgin Parts in the Car ?

If the Dealer can do it so can you

at your fingertips you have the same level of software functions as the dealer

Our kits come ready with Calibration and As built files preloaded for you so you don even need to connect online to be able to Program new Virgin Parts on some systems and on others can download on demand from JLR Server using SDD online versions

JLR PATHFINDER FAQ

What is JLR Pathfinder Software

The new JLR Pathfinder DOIP VCI is the only unit that will be compatible with all JLR vehicles with the new MY17 vehicle architectures. In addition to the 17MY vehicle line applications, the DOIP VCI will be capable of interfacing with 14-16MY Multi-CAN architecture vehicle lines on the Pathfinder diagnostic system.

Which Land Rover Jaguar Model use Doip Pathfinder ?

> 17MY > Range Rover / L405

> 17MY > Range Rover Sport / L494
> 18MY > Discovery / L462
> 18MY > Range Rover Velar / L560
> 18MY > Evoque / L538
> 18MY > Discovery Sport / L550
> 18MY > XF / X260
> 18MY > XE / X760
> 18MY > F-PACE / X761
> 18MY > F-TYPE / X152
> 18MY > E-PACE / X540

> 19MY > I-PACE / X590

What do I need to use PATHFINDER for ?

Panasonic Toughbook / Toughpad

JLR Approved Diagnostic Equipment For PATHFINDER to operate at its very best, the laptop or tablet being used must be an approved version/level of hardware.

Note: For further information on approved hardware to support PATHFINDER, refer to: - Administration Bulletins JAB00046 / LAB00051

Downloading and Installing PATHFINDER

Installing PATHFINDER software

Note:

The PATHFINDER software is designed to be installed to your existing JLR Approved Diagnostic Equipment. Please make sure you have the latest level of SDD software installed before beginning the PATHFINDER software installation.
Make sure there are no external USB flash drives inserted into the machine.
Due to software file size, the software download and installation process will take some time.

Downloading and Installing PATHFINDER

Make sure that the approved hardware is connected to the internet.
Open Internet Explorer
Using the following URL, Download the PATHFINDER software:
1. DOWN LOAD PATHFINDER UPDATER
Select ‘Save’, select ‘Desktop’, select ‘Save’.
The software file will now download.
Select ‘Run’.
A security warning window will appear, select ‘Run’.
The Jaguar Land Rover Connect Setup Wizard will now begin.
The ‘Welcome to the Jaguar Land Rover Connect Setup Wizard’ pop up will appear. Select ‘Next’.
The 'Select Additional Tasks' pop up will appear. Do not select the ‘Create a desktop icon’. Select ‘Next’.
1. Note: The installation progress will be shown on screen.
After installation, the 'Completing the Jaguar Land Rover Connect Setup Wizard' will appear. Select ‘Finish’.
The machine will now restart.
The Internet Explorer will open with your homepage or the new JLR App Launcher screen will open.
1. Note: The PATHFINDER icon will not work until the software download has completed.
The PATHFINDER software will automatically download in the background.
1. Note: To check the software download progress, select the ‘Hidden Icon’ arrow in the bottom right hand of the screen (Windows system tray). Right click the ‘Connect’ icon, select ‘Check for Updates’ and view the Jaguar Land Rover Application progress bar.
2. Note: Due to software file size, the software download and installation process will take some time, please be patient.
3. Note: Do not attempt to use PATHFINDER or SDD until the software download and installation has completed.
The ‘Jaguar Land Rover Connect Updater’ pop up will appear, select ‘Install Now’.
1. Note: If the ‘Please close JLRAppLauncher to continue the installation’ pop up appears, hover the cursor over the ‘JLR Application Launcher’ icon on the ‘Windows Task Bar’ at the bottom of the screen. Right click on the icon and select ‘Close Window’. Select ‘Continue’ on the ‘JLRAppLauncher message’ pop up.
The ‘JLRAppLauncher message’ pop up will close, PATHFINDER is now installing, please be patient.
Select the ‘Hidden Icon’ arrow in the bottom right hand of the screen (Windows system tray). Select the ‘Connect’ icon and view the ‘Jaguar Land Rover Application progress bar.
When the progress bars display 100%, select ‘Close’.
PATHFINDER is now installed.

Installing the Diagnostics over Internet Protocol (DoIP) Vehicle Communication Interface (VCI) unit

Installing the Diagnostics over Internet Protocol (DoIP) Vehicle Communication Interface (VCI) unit

Note:

PATHFINDER requires a DoIP VCI unit to communicate with the 2017 model year Range Rover L405, Range Rover Sport L494 and New Discovery L462.
The DoIP VCI must be the only VCI connected to the JLR Approved Diagnostic Equipment when using PATHFINDER. Future PATHFINDER communications will appear soon in the ‘Activity Stream’ section on TOPIx. Every retailer MUST have the DoIP VCI available in their workshop. The DoIP VCI is the only JLR approved VCI unit that can communicate with the 2017 model year vehicles identified earlier.
Please be aware that the following instructions are only applicable for the first use of the VCI. Once the initial installation and settings have been completed, the DoIP VCI is plug and play with the PATHFINDER software.

Insert the DoIP VCI USB cable into the DoIP VCI device and the JLR Approved Diagnostic Equipment.
1. Note: The ‘USB Input Device’ pop up will appear, select ‘X’ and close the pop up.
Select the ‘Windows’ key.
Select ‘All Programs’.
Select ‘Bosch’.
Select ‘VCI Software (JLR)’.
Select ‘VCI Manager (JLR)’.
Select the VCI icon displayed on screen.
Select ‘Connect to VCI’
Select ‘VCI Update’.
Select ‘Start Update’.
The ‘VCI Manager Information’ pop up will appear, select ‘OK’ to continue.
1. Note: Do not disconnect the DoIP VCI from the JLR Approved Diagnostic Equipment during the update process.
2. Note: The DoIP VCI update process will take approximately 12 minutes to complete.
The DoIP VCI will now automatically restart.
Wait for the DoIP VCI to give an audible beep. Select ‘OK’ to continue.
Select ‘X’ and close the ‘VCI Manager’.
The DoIP VCI is ready for use Setting Preferences in PATHFINDER

https://www.jlridssddmongoose....

Setting Preferences in PATHFINDER

Setting Preferences in PATHFINDER

Select the PATHFINDER icon on the ‘JLR Application Launcher’.
Select ‘Other User’ and enter your ‘User Identification’ and Password details.
Select ‘Independent Operator’ or ‘Authorised Repairer’.
Select ‘OK’ and log in.
Read the content of the ‘Warning’ pop up and select ‘OK’.
Select the three bar icon in the top right of the screen. Select the ‘Settings’ icon’.
Select the ‘Communication Interface’ tab. Select ‘D-PDU’.
The ‘Windows Security Alert – Windows Firewall’ pop up is displayed.
1. Note: Do not select ‘Cancel’ when the ‘Windows Security Alert’ pop up is displayed.
In the ‘Windows Security Alert – Windows Firewall’ pop up, select the check boxes for ‘Private Networks’ and ‘Public Networks’, then select ‘Allow Access’.
The preferences have now been set in PATHFINDER.

https://www.jlridssddmongoose.com/home/activation-for-jlr-pathfinder-of-latest-version/

How Do i know when to use Pathfinder SDD or IDS on my Jaguar Land rover Range Rover ?

Which car model to use IDS on ?

Jaguars from 1995 to 2005

Which car model to use SDD on ?

Jaguar & Land Rovers from 2006 to 2017

Which car model to use PATHFINDER on ?

Pathfinder for 2017 to 2022 Models

The new protocol called DOIP and the new JLR Pathfinder DOIP VCI is the only unit that will be compatible with all JLR vehicles with the new MY17 vehicle architectures. In addition to the 17MY vehicle line applications, the DOIP VCI will be capable of interfacing with 14-16MY Multi-CAN architecture vehicle lines on the Pathfinder diagnostic system.

Some of these pathfinder vehicles listed below

> 17MY > Range Rover / L405
> 17MY > Range Rover Sport / L494
> 18MY > Discovery / L462
> 18MY > Range Rover Velar / L560
> 18MY > Evoque / L538
> 18MY > Discovery Sport / L550
> 18MY > XF / X260
> 18MY > XE / X760
> 18MY > F-PACE / X761
> 18MY > F-TYPE / X152
> 18MY > E-PACE / X540

> 19MY > I-PACE / X590

Garages and Work Shops FAQ

I own a Garage and want to offer Land Rover Jaguar Servicing or diagnostics or programming

You come to the right place as this is the source for All Diagnostics and Programming for Jaguar and LAnd Rover Vehicles from 1995 to 2019 and in to the future.

Im an independent Auto Electrician. Is this kit good for me ?

This is a Factory Dealer tool we are talking about for any auto electrician will be a very value tools in their kit.

You will be have the tech to program a vehicle from new or program existing built vehicles in any Jaguar Land Rover Factory All Vins supported Globally

Diagnostics Trouble shooting problems number 1 tool

Programming flashing module updates and programming new virgin modules in to car.

Edit CCF for vehicle and change specs etc etc

Im a Car Dealer and do alot of jags and land rover and can it benefit me ?

Before you take a Trade in you can check if Mileage is ok in Dash and BCM and other parts to confirm it.

Check and clear DTCs before selling and do module updates and custom coding if change spec before sell

Make spare keys and perform security functions

All this in house and no more wasting time calling dealers or driving to them.

All will be under your own fingertips and cur reliance

Do you offer Online Topix with wiring Diagrams and Servicing Manuals ?

All packages come without this function as standard and you need to use your own login to to login to Topix online.

For clients outside uk who cant get this we can arrange an account for this for but for UK clients not supported

Do you offer Remote Support Packages as im new to this and need Support

Software reload / Update Services

Diagnostics Support

Programming Flashing Support

Spare Key Programming Support

Lost Key Programming Support

Some support plans we offer for novice users who need support

https://www.jlridssddmongoose.com/home/sdd-support-plan-for-module-updates-diagnostics-key-programming-support-plan/

What is Teamviewer and how to use it

General

General

TeamViewer is an all-in-one solution for remote support, remote access, and online meetings which allows you to assist customers remotely, work with colleagues from a distance and also stay connected with your own devices or assist friends and family members. To connect the different devices, TeamViewer is using the TeamViewer ID, a session code or a Meeting ID.

Getting started

Getting started

To download TeamViewer, please visit our homepage at https://www.teamviewer.com and navigate to the download section by clicking on Download at the top of the page:

2019-11-06 13_12_08-.png

Alternatively, you can reach the download section via the following link: https://www.teamviewer.com/download

The download

The download

1. Please choose your operating system (=OS) to continue the download by clicking on the icon for your OS:

2019-11-06 13_13_45-.png

2. Please choose the correct TeamViewer module for the download. Depending on the OS, you can choose between different modules. If you are in doubt which module is the right for you, you can always start with the full version, which offers all features.

For Windows Users

Example for the Windows-download: Scroll to find more modules

3. To start the download, click on the Download TeamViewer button 2019-11-06 13_15_58-TeamViewer Windows Download for Remote Desktop access and collaboration.png

For Windows Users

1. The download of an .exe file starts automatically after clicking the download button.

Note: Depending on the setup of your device, you will find the download in the lower part of your screen (1) or in the download file of your computer (2):
Download completed.png (1) Download completed (visible in the bottom of the browser window(2) The file might appear in this folder

2. Open the TeamViewer_Setup.exe file by clicking on the downloaded file (single - or double-click depending on your setup)

When you see an Open file - security warning pop-up, please continue with the installation by clicking Run. Please make sure to verify the publisher shows as TeamViewer GmbH Open File - Security Warning.png

3. You can now install the TeamViewer software on your device or use it by running it only. Learn more about how to install TeamViewer in this article: How do I install TeamViewer on Windows 7, 8 and 10

TeamViewer ID

TeamViewer ID

A TeamViewer ID is a unique numeric ID assigned to each device when TeamViewer is installed. This ID is designed not to change and should remain constant even if the software is uninstalled and reinstalled.

Think of this ID like a phone number for your device. You dial the TeamViewer ID, then use the password to authenticate the connection. You can also save these ID's in the contacts list of your TeamViewer account like you would save phone numbers in the contacts list of a mobile phone.

In most of the cases a TeamViewer ID has 9 or 10 digits and you can see it on the Remote Control tab of your TeamViewer full version:

Password for spontaneous support

Password for spontaneous support

Random password

The random password is shown on the Remote Control tab of your TeamViewer application. This password is meant for spontaneous support sessions.

You can choose in the advanced options whether or when you would like TeamViewer to generate a new random password for incoming sessions (See: Random password after each session).

If you give your TeamViewer ID and the password shown underneath your ID to another person, this person will be able to connect to your device. As soon as the random password changes the person cannot access your device any longer until you give him the newly generated password.

Hint: Only allow persons you trust to remote control your device. Never give people you do not know or trust your TeamViewer ID nor password. We advise TeamViewer users to be careful with unsolicited phone calls and to not grant access to your PC to anyone you do not know or trust.

If you would like to change the random password manually you can hover with the mouse over the password field and a circle-arrow appears. Click the arrow to choose between the following options:

Create new random password
Copy random password to clipboard
Set personal password

Random Password after each session

Password for unattended access Personal password

On the full TeamViewer Remote client

When not signed in

If you want to share your ID and password with the expert, open TeamViewer Remote.

Your ID and your password will be displayed in the main interface.

When signed in

Open TeamViewer Remote.
Go to the Remote Support menu.
Your ID and your password will be displayed.

How To choose the VCM

What is a vcm and why is it needed ?

This is the link to the car and pc and come in many option

Ford VCM OBD is diagnostic programmer for vehicles 1996-2020. It can connect to various electronic control units (ECUs) and display identification, read and clear fault code memory, display and record measured values and perform actuator tests,some key programmer

The Mongoose and other J2534 compatible cables can work with SDD

for Pathfinder Doip Vci is needed as this is latest proptocols to talk with latest cars to 2021 +

types of VCMs

Their exists many VCM types and manufactures.

Ford VCM2

JLR Mongoose

Bosch KTS

Maxidas

etc etc

some are J2534 compatible and can work with SDD only

some support DOIP and can work on Pathfinder and SDD

types of protocols and year supported for vcm and protocols

For JLR is few protocols in use

CAN Mongoose ok till 2012

HS CAN This is a Faster Can and JLR VCI or BOSCH DOIP supports it till 2018

DOIP JLR Bosch This is used with Latest PAthfinder software and needs the Bosch DOIP for best results starts from 2015 to 2022+

the best device that supports all of this is the original doip from Bosch that we supply

Do you offer Free Support for Tools and Software Supplied

Is their free updates included with SDD and Pathfinder ?

When you buy from us a Laptop or Software Licence it comes for a pre definded time only and is not unlimited.

you free soft updates to newer version during the term of your licences

What is a Support plan and Do i need it ?

This depends on you

We are here to supply tools only and how to use them or update them you have to know this and is never part of any deal we make that we supply free support to you.

Support all kinds is always paid only

https://www.jlridssddmongoose....

Use this link to see the support plans we offer

Types of support include

Remote software updates

Diagnostics DTC codes clearing

Module Flashing

custom Mods

Note we are in uk and you need to choose the type of option you need support in

Faster and whats app support cost more in realtime

lower cost is email support

Teamviwer remote login support etc

What types of SDD and Pathfinder Support do you offer

Key Programming via (RFA) KVM Keyless Vehicle Module

Position of KVM in a Evoque and most Range Rovers

The position of the KVM is in the Evoque is in the boot on the left hand side of the car as the image below demonstrates

Relatively easy to take out and being able to program the keys.

Position of a KVM in a Range Rover

Please see below for the image as it demonstrates below Relatively easy to take out and being able to program the keys.

Relatively easy to take out and being able to program the keys.

Position of a KVM in a VELAR

Please see below for the image as it demonstrates below, Relatively easy to take out and being able to program the keys.

Position of a KVM in a Jaguar XF

Please see below for the image as it demonstrates below, Relatively easy to take out and being able to program the keys.

Position of a KVM in a Jaguar XJ

Please see below for the image as it demonstrates below, Relatively easy to take out and being able to program the keys.

Position of a KVM in a Jaguar F - Type

Please see below for the image as it demonstrates below, Relatively easy to take out and being able to program the keys.

Country

State/Province

City

Zip/postal code

Get rates

DIAGNOSTIC TROUBLE CODE INDEX: ANTI-LOCK BRAKE SYSTEM (ABS) - DTC: ANTI-LOCK BRAKE SYSTEM CONTROL MODULE (ABS)

DIAGNOSTIC TROUBLE CODE INDEX: ANTI-LOCK BRAKE SYSTEM (ABS) - DTC: ANTI-LOCK BRAKE SYSTEM CONTROL MODULE (ABS) (G1566096)

My account

www.Jlridssddmongoose.com

Customer Service

About us

Links

What is the difference between IDS and SDD Pathfinder & Cloud?

Will my Land Rover work with the JLR SDD Software?

Can i Do Programming with this diagnostics Kit

JLR PATHFINDER FAQ

Note:

Downloading and Installing PATHFINDER

Installing the Diagnostics over Internet Protocol (DoIP) Vehicle Communication Interface (VCI) unit

Note:

https://www.jlridssddmongoose....

Setting Preferences in PATHFINDER

How Do i know when to use Pathfinder SDD or IDS on my Jaguar Land rover Range Rover ?

Garages and Work Shops FAQ

What is Teamviewer and how to use it

General

Getting started

The download

For Windows Users

TeamViewer ID

Password for spontaneous support

Random password

On the full TeamViewer Remote client

When not signed in

When signed in

How To choose the VCM

Do you offer Free Support for Tools and Software Supplied

Key Programming via (RFA) KVM Keyless Vehicle Module

Stay Connected